This section describes how to manage and maintain the cluster using the legacy Admin Console. 

The Cluster Status page appears when logging in to the legacy Admin Console, providing a comprehensive view of the cluster as a whole and enabling cluster-wide actions, such as restarting and shutting down the cluster and modifying the cluster settings.

Authenticating Cluster-Wide Actions

Shutting down and restarting the cluster are cluster-wide actions that require authentication. Authentication is also required when changing the cluster settings to:

• Manage domains

• Modify the logging host configuration

• Change the replication multicast value

• Suspend or resume volume recovery

• Set the power-saving mode

To commit the cluster-wide actions:

1. Open the node and/or cluster configuration file with the appropriate user credentials.

2. Modify the security.administrators parameter.

An admin user is predefined in the parameter that allows Basic authentication by default. The password is sent in clear text from the browser to the legacy Admin Console.

Take the following precautions for added security:

1. Change the admin password immediately.

2. Implement real user names.

3. Encrypt user passwords using Digest authentication.

See Encrypting Defining Swarm Admins, Swarm Users, and Swarm Passwords.

Shutting Down or Restarting the Cluster

To shut down or restart all nodes in the cluster,

1. Log in to the legacy Admin Console with admin credentials.

2. Click Shutdown Cluster or Restart Cluster in the console.

3. When prompted, verify the procedure.

Finding Nodes in the Cluster

Listing of Nodes

The cluster node list provides a high-level view of the active nodes in the system. Click the maximize button next to each IP address in the Node IP column to view the storage volumes within each cluster node.

Open

The status information is transmitted periodically to the legacy Admin Console, requiring up to two minutes before the node data in the Cluster Status window is updated. Because of the status propagation delay, the data for each node may vary in comparison. Remain connected to the same node to avoid confusion for best results.

The volume labels next to each Swarm node are listed in arbitrary order. While the legacy Admin Console labels do not correspond to physical drive slots in node chassis, the volume names match the physical drives in the machine chassis. Each subcluster name must be expanded to display the corresponding volume information if the cluster is configured to use subclusters.

Search for nodes by IP address and by status if the cluster is large.

Finding Nodes by IP

Search for a node using the Node IP search field in the legacy Admin Console for large clusters with multiple nodes.

Enter the node IP address in the field and click Search to locate the targeted node.

Finding Nodes by Status

Select a Status from the drop-down menu to display nodes or volumes with a specific status.

Statuses include:

• OK: The node is working and there are no errors.

• Alert, Warning: The node or volume has experienced one or more errors. Click the IP Address link to drill down to the node and view the related error.

• Initializing: The short state after a node boot when it is reading cluster persisted settings and is not quite ready to accept requests.

• Maintenance: The node has been shut down or rebooted by an administrator from either SNMP or the legacy Admin Console and should not be considered missing for recovery purposes. By default, a node can be in a Maintenance state for 3 hours before it transitions to Offline and the cluster starts recovery of its content. Maintenance mode is not initialized when the power is manually cycled on the node outside of Swarm (either physically on the hardware or via a remote shutdown mechanism like iDRAC) or if there is a disk error; in both these instances, recovery processes are started for the node unless recovery is suspended.

• Mounting: The node is mounting one or more volumes, including formatting the disk if it is new and reading all objects on the volume into the RAM index for faster access.

• Offline: The node or volume was previously but is no longer present in the cluster.

• Retiring: The node or volume is in the process of retiring, verifying all objects are fully protected elsewhere in the cluster and then removing them locally.

• Retired: The node or volume has completed the retiring process and may be removed from the cluster.

• Idle: The nodes or volumes are in power-saving mode due to a period of configurable inactivity. (See Configuring Power Management.)

Only matching results appear on the console when a value in the drop-down menu is selected. Select View All to redisplay all nodes in the cluster when finished looking at the searched node(s).

Percent Used Indicator

The % Used indicator provides a helpful computation of cluster availability and licensed and total physical space for monitoring purposes. Space used is calculated against the lesser of the total physical space or the licensed space.

For example, in a cluster with 4 TB of physical space but only 2 TB of licensed space where 1.5 TB of space is used, the console reports 75% Space Used.

The indicators include color highlighting, as described below.

Displaying Subcluster Information

The Node List is grouped first by subcluster name and then by node IP address if the cluster contains subclusters. The subcluster name is an IP address if no subcluster name is specified in the node or cluster configuration file. The first row of each subcluster includes a roll-up of the status for the nodes in the subcluster.

Example of two subclusters expanded to show member nodes:

Open

The status information is transmitted periodically to the legacy Admin Console, requiring up to two minutes before the node data in the Cluster Status page is updated. The data for each node may vary in comparison because of the status propagation delay.