Upgrading to the Latest SCS Version for CentOS 7

Directly upgrading from SCS 1.2 to SCS 1.3 is not supported, but this limitation is removed starting with SCS 1.4. Swarm supports upgrading from SCS 1.1, 1.2, or 1.3 to SCS 1.4 and booting from Storage bundle v15.0 with multicast disabled.

Upgrade Notes

Any version before SCS 1.4 cannot boot versions of Swarm storage that include the optional multicast feature (version 15.0 and later). This is due to changes required in SCS to support this feature.
Complete the SCS upgrade first if upgrading both SCS and Swarm Storage simultaneously. Then add the new Swarm Storage component to the SCS repo (using scsctl repo component add ...). During this process, scsctl will prompt as to whether or not to enable multicast for the storage cluster by asking to set a value for cip.multicastEnabled. Select True to enable the use of multicast (this matches the behavior of prior versions of Swarm), or False to disable it. If you are unsure which to choose, contact DataCore Support.

Refer to the following steps to upgrade SCS:

If static IP addresses were previously assigned before this upgrade, skip this step and proceed to step#2.
1. Allow DHCP to assign IP addresses
  When the cluster nodes are rebooted, DHCP will assign an IP address to each node. If the nodes have already been booted with manually assigned IPs, the assigned IP addresses will remain the same. If IP addresses were not manually assigned, but existing DHCP leases are still in effect, then currently assigned IP addresses will remain the same. If existing DHCP leases have expired (or this is the first boot of the storage cluster), DHCP will assign IP addresses from the allocated pool in no particular order, so proceed to “Boot/reboot” Swarm nodes.
2. Pre-assign an IP address to each storage node
  In this case, an IP address must be manually assigned to each storage node before it is rebooted. The procedure for manual assignment is fully explained in Configuring Swarm for Static IPs with Swarm Cluster Services (SCS)).
  The summary of the manual assignment procedure is:
  1. Get an instance list that provides a node ID to use in the next step.
    scsctl storage instance list
  2. Assign an IP address to each node.
    scsctl storage config set -d -i {chassis ID} "network.ipV4Address={your.static.address.here}"
Install the new RPM.
```
rpm -Uvh swarm-scs-[version].x86_64.rpm
```
Run the following command.
```
scsctl diagnostics upgrade_check
```

Note

Refer to the following step if an error occurs during the upgrade_check command:

systemctl restart swarm-platform && sleep 90

Run the diagnostics check.

scsctl diagnostics config scan_missing

It shows the below output:

Running step [11/11]: Show the next steps after this wizard
  ********************************************************************************
  Congratulations, your Swarm Cluster Services server has been upgraded!
  Please reboot, then run the following to ensure your system is fully configured:

Reboot the system.

Re-initialize DHCP.

scsctl init dhcp --dhcp-reserve-lower [integer]

Choose the SCS version to activate the latest version.
```
scsctl platform software activate
```

Info

A customer might see the below error in the output while upgrading to SCS 1.7 or above, but this is safe to ignore it.

Running step [4/11]: Re-enable systemd management of SCS Linux services
  Disabling service "swarm-platform.service" for pod "swarm-platform"...
  Failed to disable services: b'Failed to execute operation: No such file or directory\n'
  Deleting service file for pod "swarm-platform": /etc/systemd/system/swarm-platform.service [exists: False, symlink: True]
  Retry: Disabling service "swarm-platform.service" for pod "swarm-platform"...

We would need some additional necessary steps to upgrade directly from SCS 1.4 to 1.7.1 under the following conditions:

The current instance is using static IP assignments for storage nodes, using the node.cfg template method.
The storage cluster supported by the current instance is running a version of CAStor that does not support direct IP assignment, a version of CAStor that does not include the setting, “network.useStaticAddresses”.

When the above conditions are absent, upgrading SCS and the storage software will go smoothly as described above.

When these conditions are true, the upgrade process requires additional steps:

After SCS is upgraded to 1.7.1, the storage software must be upgraded to the most recent version or any version that supports direct IP assignment and includes the “network.useStaticAddresses” setting.
After the new storage software version is activated, the storage cluster must be rebooted before any direct IP assignment is performed.

After these additional steps, the direct assignment of static IPs and the unsetting of the node.cfg templates can proceed as usual. The cluster gets rebooted again once that process is completed.

When restarting an entire cluster all at once, verify nodes that were already part of the cluster are restarted first. Once they are fully online, it is safe to boot any new nodes being added into the cluster. Booting these new nodes too early can lead to IP address conflicts, and the new nodes will fail to come online.